HORMANN UAP1 PDF

Find great deals for Hörmann Universaladapterplatine UAP 1. Shop with confidence on eBay!. For Hörmann door, Type: SupraMatic, Rotamatic / P / PL from year 09/ and LineaMatic built from 10/ – About for direction selection (up / stop / close). For inputs to Hormann: does it mean that I have to run 6 wires for this section from Loxone to Hormann? Or is it possible to reuse the wire for

Author: Tujind Tozshura
Country: Uganda
Language: English (Spanish)
Genre: Music
Published (Last): 11 November 2008
Pages: 59
PDF File Size: 19.69 Mb
ePub File Size: 4.38 Mb
ISBN: 593-7-58744-583-8
Downloads: 93327
Price: Free* [*Free Regsitration Required]
Uploader: JoJomuro

Email Required, but never shown. Burglar alarm As you can see the only status bit set, is from the second byte ua;1 means reversing according to the patent which makes no sense to me.

Reverse engeneering the Hörmann UAP1 protocoll

Any help would be greatly appreciated. Pedestrian door Bit 6: To control the door via a home automation system you have several options: The changed partial opening position is saved.

Sign up using Email and Password. Unfortunately the patent doesn’t say anything about the device codes. Speak directly to the motor and get the signals directly onto the homeautomation system.

Hörmann Universaladapterplatine UAP 1

Light on Bit 1: That being said you might be able to program a button to activate open when pressed and to also activate the same function on release.

By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy aup1 cookie policyand that your continued use of the website is subject to these policies.

To control the door via a home automation system uap11 have several options:. The message can be between 1 and 3 bytes long and the patent states that it can be expanded.

  HERPETOFAUNA DA CAATINGA PDF

Hörmann Universaladapterplatine UAP 1 | eBay

Here’s what I got using the USB converter with the door closed idling: After having discussed that issue with my Italian friend he was able to figure out the polynom 0x07 as well as the initial value 0xF3 for the CRC algorithm. Reverse engeneering the protocoll I expected a rather simple protocoll where no comunication happens until the UAP1 gets triggered by a switch, but I was more than wrong.

Fortunately hormanj page gives you a nice lookup table for the CRC values which I then used in my Python program to verify all the messages I’ve recorded so far. I tried some CRC brute force attempts but without success.

Press the PRG button until the decimal point next to the menu number is illuminated.

After being able to seperate the byte stream into messages, I still wasn’t able to calculate the checksum. Connect potential free contacts directly to the motor.

Not much to see here, just that all pins of the 6-pin RJ12 sockets are directly conected to each other.

I am an electronics amateur and can’t figure out based on the schematic below if that is correct? I see one for your supramatic seems a bit over complicated for a Garage Door – however reading the instructions for the ventilation position You might find what you need here. Bottom side of the circuit board: Currently I send a 0. The status fully closed, fully open, mid drive works perfectly fine, however I am having issues with the motion commands move up, move down, stopas they only work sometimes and in some directions – which is most likely due to me wiring it up incorrectly however the guide linked above is not very specific about the wiring etc.

Exactly what I want to have: Hi Ken, as you say in the beginning of the reply the UAP enables me to “open the garage door” and “close the garage door” which is what I want to achieve same as what the person who wrote the guide I linked to achievedsorry if I didn’t explain properly.

  CRESTRON DM-TX-200-C-2G-B-T PDF

Radio control getting teached Bit 2: If the selected height is too low, a 2-digit number starting with 1 will appear with a flashing decimal point see section Top side of the circuit board: Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

At startup the Master scans the bus for devices. Move the door into the desired position with the buttons andvia the taught-in radio code impulse or an external control element with impulse function.

low voltage – Hormann garage door opener automation with Loxone – Home Improvement Stack Exchange

These are the messages I was able to make sense of so far. When the board is powered while the logic analyzer is collecting data, we see these bytes comming in:. The CRC checksum After being able to seperate hprmann byte stream into messages, I still wasn’t able to calculate the checksum.

Learning button assignment Bit 7: But how can I tell who is sending which bytes!? Could it be that you 0. Here’s what I got using the USB converter with the door closed idling:. Thanks for looking into this!